Blade Steel Comparison Chart
This blade steel comparison chart puts 57 of the most popular knife steels side by side, from premium powder steels like MagnaCut, M390, K390, and S90V to budget favorites like D2, 14C28N, 9Cr18MoV, 8Cr13MoV, and 440A. Tap any column header to sort the chart by the property that matters most to you. Every rating in this blade steel comparison uses a 1–10 scale, where 10 is the best performance in that category.
Super Steels are the $$$ and $$$$ price tiers. Budget Steels are $ and $$.
| Steel | Edge Retention | Toughness | Corrosion Resistance | Ease of Sharpening | Price Tier | Best For |
|---|---|---|---|---|---|---|
| CPM MagnaCut | 7 | 8 | 9 | 5 | $$$ | All-around premium EDC |
| CPM-S30V | 7 | 5 | 7 | 4 | $$$ | Long-lasting working edge |
| CPM-S35VN | 6 | 6 | 7 | 5 | $$$ | Balanced premium EDC |
| CPM-S45VN | 7 | 6 | 8 | 4 | $$$ | Upgraded premium EDC |
| CPM-S90V | 10 | 3 | 7 | 1 | $$$$ | Extreme edge retention |
| CPM-S110V | 10 | 2 | 8 | 1 | $$$$ | Extreme edge retention, stainless |
| Maxamet | 10 | 2 | 3 | 1 | $$$$ | Collectors, maximum hardness |
| CPM-Rex 121 | 10 | 2 | 2 | 1 | $$$$ | Collectors, maximum edge |
| CPM-15V | 10 | 2 | 1 | 1 | $$$$ | Spyderco sprints, extreme edge retention |
| CPM-10V | 9 | 4 | 1 | 2 | $$$$ | Extreme edge retention, carbon steel |
| Böhler M390 / CPM-20CV / CTS-204P | 8 | 4 | 9 | 3 | $$$$ | Maximum edge retention |
| Böhler M398 | 9 | 3 | 8 | 2 | $$$$ | Longer edge life than M390 |
| Böhler K390 | 9 | 7 | 1 | 2 | $$$$ | Extreme edge retention with toughness |
| CTS-XHP | 7 | 5 | 8 | 4 | $$$ | Edge holding with rust resistance |
| Böhler ELMAX | 7 | 6 | 8 | 5 | $$$ | Well-rounded premium EDC |
| Böhler Vanax | 5 | 6 | 10 | 6 | $$$$ | Saltwater and marine use |
| LC200N / Cronidur 30 | 4 | 8 | 10 | 7 | $$$ | Saltwater, Vanax alternative |
| H1 | 2 | 7 | 10 | 7 | $$$ | Saltwater, rustproof |
| SLD-MAGIC | 7 | 6 | 4 | 4 | $$$ | Enthusiasts and collectors |
| ZDP-189 | 8 | 2 | 6 | 3 | $$$ | Japanese high-hardness slicers |
| SG2 / R2 | 7 | 4 | 7 | 5 | $$$ | Japanese premium kitchen and EDC |
| CPM-3V | 5 | 10 | 2 | 6 | $$$ | Hard-use outdoor and survival |
| CPM-CruWear / Z-Wear / PD1 | 6 | 8 | 3 | 5 | $$$ | Hard-use EDC |
| CPM-4V | 7 | 8 | 2 | 4 | $$$ | Tough working edge |
| Vanadis 4 Extra | 7 | 9 | 2 | 4 | $$$ | Tough, high-wear working blades |
| CPM-M4 | 8 | 6 | 2 | 3 | $$$ | High-performance working knives |
| CPM-Rex 45 | 8 | 5 | 2 | 3 | $$$ | Spyderco sprints, high-hardness working edge |
| HAP40 | 8 | 4 | 2 | 3 | $$$ | Japanese high-speed steel sprints |
| CPM-154 | 5 | 6 | 7 | 6 | $$ | Refined mid-range EDC |
| CTS-BD1N | 5 | 6 | 7 | 6 | $$ | Mid-range Spyderco EDC |
| 154CM | 5 | 5 | 6 | 6 | $$ | Classic American EDC |
| Böhler N690 | 4 | 5 | 8 | 7 | $$ | European mid-range EDC |
| 14C28N | 3 | 8 | 8 | 9 | $$ | Tough, low-maintenance budget blades |
| AEB-L | 3 | 9 | 7 | 9 | $$ | Thin slicers and tough budget blades |
| Sandvik 12C27 | 3 | 7 | 7 | 9 | $ | Scandinavian and traditional knives |
| Nitro-V | 3 | 7 | 8 | 8 | $$ | Budget hard-use and outdoors |
| VG-10 | 4 | 4 | 7 | 7 | $$ | Kitchen and slicing |
| 10Cr15CoMoV | 4 | 4 | 7 | 7 | $$ | Budget VG-10 alternative |
| AUS-10 | 4 | 5 | 6 | 7 | $$ | Upgraded budget EDC |
| D2 | 5 | 3 | 3 | 5 | $ | Budget edge holding |
| DC53 | 5 | 7 | 2 | 5 | $ | Budget tough tool steel |
| 440C | 4 | 4 | 6 | 7 | $ | Traditional stainless blades |
| 9Cr18MoV | 4 | 4 | 6 | 7 | $ | Budget 440C alternative |
| AUS-8 | 3 | 6 | 6 | 8 | $ | Budget all-rounder |
| A2 | 4 | 7 | 2 | 7 | $$ | Classic fixed blades |
| 52100 | 4 | 8 | 1 | 8 | $$ | Custom and premium carbon steel blades |
| O1 | 4 | 6 | 1 | 9 | $ | Custom and bushcraft knives |
| 1095 | 3 | 7 | 1 | 9 | $ | Bushcraft and traditional knives |
| 80CrV2 | 3 | 8 | 1 | 9 | $ | Budget fixed blades and choppers |
| 1075 / 1080 | 2 | 8 | 1 | 9 | $ | Budget bushcraft and machetes |
| 5160 | 2 | 9 | 1 | 9 | $ | Choppers, machetes, and swords |
| 8Cr13MoV | 2 | 6 | 5 | 9 | $ | Entry-level beater knives |
| 8Cr14MoV | 2 | 6 | 5 | 9 | $ | Spyderco budget folders |
| 440A | 2 | 6 | 7 | 9 | $ | Budget traditional and Rough Ryder knives |
| 7Cr17MoV | 2 | 6 | 6 | 9 | $ | Budget 440A alternative |
| 420HC / Case Tru-Sharp | 2 | 7 | 7 | 10 | $ | Multi-tools, Case knives, and easy field sharpening |
| 5Cr15MoV | 1 | 7 | 6 | 10 | $ | Cheap folders and kitchen knives |
How to Choose the Right Blade Steel
Every blade steel comparison comes down to trade-offs. The steels that hold an edge longest usually give up some toughness and take more effort to sharpen, while the easiest steels to sharpen dull faster. No steel wins every column in the chart, so the right choice depends on how you use your knife and how much maintenance you’re willing to do.
Start With How You Use Your Knife
If most of your cutting is opening boxes, breaking down cardboard, and cutting tape or cord, edge retention is the column to watch. Cardboard is surprisingly abrasive, and steels like S90V, S110V, M398, K390, M390, 20CV, CTS-XHP, S45VN, and MagnaCut go noticeably longer between sharpenings. S90V, S110V, CPM-15V, Maxamet, and Rex 121 share the top score for edge life, but they’re also the hardest steels in the chart to sharpen. K390 is the standout if you want long edge life without giving up much toughness.
If you baton wood, pry, or use your knife hard outdoors, prioritize toughness instead. CPM-3V is the toughest steel in this chart and a favorite for fixed blades and survival knives, with 5160, Vanadis 4 Extra, and AEB-L close behind. CPM-CruWear, CPM-4V, LC200N, MagnaCut, 14C28N, Nitro-V, 52100, 80CrV2, 1075, DC53, 1095, and 420HC are also much less likely to chip or snap than harder, carbide-heavy steels like D2, M390, S90V, or ZDP-189.
Consider Where You Carry
Sweat, humidity, salt air, and food acids all cause rust. If you pocket-carry all day, spend time near the water, or cut food with your EDC, pick a steel with a high corrosion score such as Vanax, LC200N, H1, MagnaCut, M390, or 14C28N. Vanax and LC200N are nitrogen-based steels that are about as close to rustproof as a knife steel gets, and H1 is effectively rustproof even in saltwater, which makes all three top choices for fishing, diving, and boating knives.
D2, DC53, CPM-CruWear, and SLD-MAGIC are only semi-stainless and will spot if they’re left wet, so they reward owners who wipe their blades down. CPM-3V, CPM-4V, Vanadis 4 Extra, CPM-M4, Rex 45, HAP40, CPM-10V, CPM-15V, K390, Rex 121, Maxamet, A2, O1, 52100, 80CrV2, 5160, 1075, and 1095 are not stainless at all. They need a protective coating or regular oiling, and the simple carbon steels like 1095 will develop a patina with use.
Be Honest About Sharpening
High-vanadium steels like S90V, S110V, CPM-15V, CPM-10V, K390, M398, M390, S30V, S45VN, and S35VN are packed with extremely hard vanadium carbides. That’s why they hold an edge so long, but it also means they sharpen slowly on conventional stones, and you’ll want diamond plates or a guided system when they finally dull. S90V, S110V, CPM-15V, Maxamet, and Rex 121 are the most demanding steels in this blade steel comparison to sharpen. If you’d rather do a quick touch-up on a basic stone, 420HC, Case Tru-Sharp, 5Cr15MoV, 12C27, AEB-L, 1095, O1, 440A, 8Cr13MoV, 8Cr14MoV, 14C28N, Nitro-V, and AUS-8 all sharpen easily.
Match the Steel to Your Budget
Powder metallurgy steels like MagnaCut, S30V, S35VN, S45VN, S90V, S110V, CPM-15V, K390, M398, Vanadis 4 Extra, CruWear, CTS-XHP, ELMAX, Vanax, and M390 cost more to produce and usually appear on higher-priced knives. Mid-range options like 154CM, CPM-154, CTS-BD1N, and Böhler N690 offer a nice step up from budget steels without premium pricing.
Budget steels like 5Cr15MoV, 7Cr17MoV, 8Cr13MoV, 8Cr14MoV, 9Cr18MoV, 10Cr15CoMoV, 440A, D2, DC53, 440C, 12C27, 14C28N, AEB-L, and Nitro-V dominate the lower price ranges, and 14C28N, AEB-L, and Nitro-V in particular perform well above their price. Chinese steels like 7Cr17MoV, 9Cr18MoV, and 10Cr15CoMoV are close equivalents of 440A, 440C, and VG-10, so they’re a good sign of value on a budget knife. For a first knife, a well-made 14C28N or D2 folder is a better buy than a premium steel in a poorly built knife.
Heat Treatment Matters as Much as the Steel
The ratings in this chart assume a good heat treatment, and that’s true of any blade steel comparison you’ll find online. A well-treated 14C28N can outperform a poorly treated S30V, and budget D2 in particular varies widely from brand to brand. A maker’s reputation for consistent heat treatment is just as important as the steel listed on the spec sheet.
Quick Picks
Want the short version of this blade steel comparison? Here’s where each steel comes out on top:
- Best all-around: CPM MagnaCut
- Longest edge retention: CPM-S90V or CPM-S110V
- Best edge retention with toughness: Böhler K390
- Best edge retention with easier upkeep: Böhler M390 / CPM-20CV / CTS-204P
- Toughest: CPM-3V
- Best hard-use EDC: CPM-CruWear
- Most rust resistant: Böhler Vanax, LC200N, or H1
- Best budget steel: 14C28N or Nitro-V
- Best budget edge holding: D2
- Best budget tough steel: AEB-L or DC53
- Best mid-range steel: CPM-154, CTS-BD1N, or Böhler N690
- Best for bushcraft: 1095, 80CrV2, or CPM-3V
- Best for choppers and machetes: 5160 or 1075
- Easiest to sharpen: 420HC / Case Tru-Sharp
Blade Steel Comparison Chart FAQ
What is the best all-around knife steel?
For most people, CPM MagnaCut. It combines high toughness, excellent corrosion resistance, and good edge retention in a single steel, a balance older steels forced you to trade away. It was designed by metallurgist Larrin Thomas and released in 2021, and it has quickly become the go-to steel for premium EDC knives. If you want the longest possible edge life and don’t mind harder sharpening, M390, 20CV, or S90V is the alternative.
Is MagnaCut worth the price?
If you want one knife that handles everything with minimal maintenance, yes. If your cutting is mostly light tasks and you touch up your edge regularly, a budget steel like 14C28N or Nitro-V gets you most of the way there for a fraction of the cost.
Is D2 a good knife steel?
D2 is a solid budget steel that holds an edge better than most steels in its price range. The trade-offs are lower toughness, only moderate rust resistance, and quality that varies a lot with heat treatment. It’s a great value if you keep your knife dry and don’t use it for prying or heavy impacts.
Is D2 better than 8Cr13MoV?
For edge retention, yes, and the difference is noticeable. 8Cr13MoV is tougher, more rust resistant, and much easier to sharpen, though. Choose D2 if you want an edge that lasts longer, or 8Cr13MoV if you want a low-maintenance beater that’s quick to touch up.
Is 8Cr14MoV the same as 8Cr13MoV?
Nearly. 8Cr14MoV has slightly more chromium, but the two perform almost identically. Spyderco uses 8Cr14MoV on budget models like the Tenacious and Persistence, and a good heat treatment matters far more than the one-digit difference in the name.
What is 440A steel?
440A is the lowest-carbon member of the 440 family. It’s very rust resistant, tough, and easy to sharpen, but it doesn’t hold an edge as long as 440C. Rough Ryder uses it on most of its traditional knives, and 7Cr17MoV is a close Chinese equivalent.
Is Case Tru-Sharp a good steel?
For traditional pocket knives, yes. Tru-Sharp is Case’s name for its 420HC-class stainless steel. It resists rust well and sharpens very easily, though it won’t hold an edge as long as harder modern steels. It’s a sensible choice for slip joints that see light everyday work.
What is the difference between S30V and S35VN?
S35VN was developed by Crucible as an improvement on S30V. It swaps some of the vanadium for niobium, which gives it a finer structure, slightly better toughness, and easier sharpening, at the cost of slightly lower edge retention. In real-world use the difference is small.
Is S45VN better than S35VN?
Slightly. S45VN is the newest step in the S30V family. It adds a bit more chromium and niobium, which improves corrosion resistance and edge retention over S35VN while keeping similar toughness. Many brands have moved their premium knives from S35VN to S45VN, and it’s an easy steel to recommend.
Is S90V better than M390?
For edge retention, yes. S90V has much more vanadium than M390 and holds an edge noticeably longer in slicing tests. The trade-off is that it’s less tough and much harder to sharpen, so it suits users who cut a lot of abrasive material and own diamond sharpening gear. M390 is the better choice for most people who want long edge life without as much sharpening effort.
Is M390 the same as 20CV and 204P?
Nearly. Böhler M390 is made in Austria, CPM-20CV is made by Crucible in the United States, and CTS-204P is made by Carpenter, also in the United States. Their compositions are almost identical and they perform essentially the same. In any blade steel comparison, you can treat them as interchangeable.
What is the difference between M390 and M398?
M398 is a newer Böhler powder steel with more carbon and vanadium than M390. That gives it noticeably longer edge retention, but it gives up some toughness and is harder to sharpen. M390 remains the more balanced choice for most EDC users.
What is the difference between M390 and ELMAX?
Both are Böhler powder steels. M390 holds an edge longer and resists corrosion a little better, while ELMAX is somewhat tougher and easier to sharpen. ELMAX is a great choice if you want premium performance with less chipping risk and simpler maintenance.
What is the difference between 154CM and CPM-154?
They share the same chemistry, but CPM-154 is made with Crucible’s powder metallurgy process. That gives it a finer, more uniform structure, which translates to slightly better toughness, a cleaner edge, and easier polishing. 154CM is the classic version and is still a reliable American steel used by brands like Benchmade.
Is 440C a good knife steel?
440C is a dependable, old-school stainless steel. It holds an edge reasonably well, resists rust decently, and is easy to sharpen. Newer steels outperform it in most areas, but a well-made 440C knife is still a perfectly good tool for everyday tasks.
What is the toughest knife steel?
In this chart, CPM-3V is the toughest by a wide margin. It’s designed to resist chipping and breaking under heavy impact, which is why it’s popular for fixed blades, choppers, and survival knives. The downside is low corrosion resistance, so most 3V blades come coated. 5160 and Vanadis 4 Extra are also extremely tough. If you want toughness with good rust resistance, AEB-L and MagnaCut are the closest stainless alternatives.
Is 1095 a good knife steel?
For bushcraft and traditional knives, yes. 1095 is a simple high-carbon steel that’s tough, easy to sharpen in the field, and inexpensive. It will rust if neglected and develops a patina over time, so it’s best for owners who don’t mind oiling their blade. It’s also a favorite for striking a ferro rod with the spine.
What is 52100 steel?
52100 is a high-carbon bearing steel that’s a favorite of custom makers. With a good heat treatment, it’s very tough, takes a fine edge, and sharpens easily. It isn’t stainless, so it needs oiling or a coating, and it develops a patina like 1095.
What is Nitro-V steel?
Nitro-V is a budget stainless steel based on AEB-L, with added nitrogen and vanadium. It’s tough, rust resistant, and easy to sharpen, much like 14C28N. It’s a great choice for affordable outdoor and EDC knives that need to handle hard use with little maintenance.
What is 9Cr18MoV steel?
9Cr18MoV is a Chinese stainless steel that’s roughly equivalent to 440C. It holds an edge a bit better than 8Cr13MoV, resists rust reasonably well, and is easy to sharpen. It’s common on budget folders and is a solid step up from entry-level steels.
Is 10Cr15CoMoV the same as VG-10?
Close to it. 10Cr15CoMoV is a Chinese steel with a composition very similar to VG-10, including the cobalt. Performance is comparable, though results depend more on the maker’s heat treatment than on the steel name.
Is DC53 a good knife steel?
DC53 is an improved version of D2 that’s noticeably tougher with similar edge retention. Like D2, it’s only semi-stainless, so keep it dry. It’s a great value on budget knives built for harder use.
What is the difference between 14C28N and AEB-L?
Both are fine-grained Sandvik-style stainless steels that are tough and easy to sharpen. AEB-L is a little tougher and excels on thin slicing edges, while 14C28N adds nitrogen for better corrosion resistance. Nitro-V is based on AEB-L.
Is N690 better than D2?
It depends on what you value. Böhler N690 is far more rust resistant and a bit easier to sharpen, while D2 holds an edge slightly longer. N690 is a great choice for an EDC that sees sweat and humidity.
Is K390 better than M390?
For edge retention and toughness, yes. K390 holds an edge longer than M390 and is much tougher. The catch is that K390 is not stainless, so it needs to be kept dry or oiled. M390 is the better pick if rust resistance matters to you.
What is CPM-CruWear steel?
CruWear is a tough tool steel with better edge retention than CPM-3V. It’s semi-stainless, so it needs a little care, but it has become a favorite for hard-use EDC folders that can take abuse without chipping. Z-Wear (from Zapp) and PD1 (from Carpenter) are essentially the same steel under different names.
What is the difference between LC200N and H1?
Both are nearly rustproof, making them top picks for saltwater use. LC200N holds an edge noticeably better and is the more refined steel. H1 is softer and holds an edge less well, but it is effectively immune to rust.
What is SLD-MAGIC steel?
SLD-MAGIC is a Japanese tool steel from Proterial (formerly Hitachi Metals). It’s known for a strong mix of edge retention and toughness for a tool steel, but like D2 it’s only semi-stainless. It shows up mostly on limited-run and enthusiast knives, so it’s more of a collector’s steel than an everyday choice.
What knife steel is easiest to sharpen?
In this chart, 420HC (including Case Tru-Sharp) and 5Cr15MoV are the easiest, followed by 12C27, AEB-L, 14C28N, 1095, O1, 440A, and 8Cr13MoV. These steels have low carbide content, so they respond quickly to basic stones, pull-through sharpeners, and field sharpening.
Which knife steel is most rust resistant?
Vanax, LC200N, and H1 share the top corrosion score in this chart and are the best choices for saltwater and diving knives. MagnaCut and M390/20CV/204P are the most rust-resistant steels that also offer strong all-around performance.
How are the ratings in this blade steel comparison determined?
Each score is a relative rating from 1 to 10 based on published steel testing data and real-world use. The scores compare the steels to each other rather than measuring them against a fixed lab standard, so a 7 in edge retention means that steel holds an edge better than a 5, not that it hits a specific test number. Your results can vary with blade geometry, edge angle, and heat treatment.
Does heat treatment matter more than the steel?
It often matters just as much. The same steel can perform very differently depending on how it was hardened and tempered, which is why reputable makers with consistent heat treatment are worth paying attention to.
